Industrial Grade High Strength Epoxy Adhesive 10 ML Cartridge w/ 2 TIPS 10 PACK

Description

Technical Product Bulletin
FAST CURE IDUSTRIAL GRADE EPOXY ADHESIVE
Takes 2 hours to hold and harden.  Do not move after 4 minutes until it fully cures.
You have 4 minute work time which is the amount of time you have to apply the product before it begins to dry.  Must work fast.  ** Buy AA-BOND 28 if you need 1 hour work time.
Industrial grade bond to all substrates.  The only two substrates which exhibit a weak bond are rubber and plastics.
Comes with two mixing tips.  Simply remove cap, twist and dispense product through the mixing tip.
The mixing tip will not be usable if you stop dispensing for an hour.  Keep tip attached until next use at which time you can replace it.
This 10ML cartridge also comes with a plunger so a dispensing gun is not needed.
This product is odorless / solvent free
PRODUCT DESCRIPTION:
AA-BOND 201 is an exceptional epoxy formulation recommended for lower temperature or wet industrial bonding applications where
FAST CURING is required.
AA-BOND 201 is versatile two-part epoxy system contains no solvents, mixes easily at room temperature, and is suitable for high
performance structural bonding applications where the combination of very fast room temperature curing coupled with low shrinkage
and
excellent mechanical and electrical properties is needed.
AA-BOND 201 develops strong, tough bonds to metals, plastics, glass and glass fabrics, hardboards and forestry products, ceramics,
rubber, masonry materials, and other construction materials.
AA-BOND 201 is an excellent electrical insulator, and provides superior resistance to vapors and gases, water, galvanic action, petroleum
fuels, salt solutions, and many other organic and inorganic compounds
AA-BOND 201 develops significant properties 1 hour after mixing. However, an extended cure of 4-6 hours at 25°C is required for full
matured bonds.
Note:
AA-BOND 201 develops a high exotherm. Use immediately after mixing. The exothermic reaction begins within 2 minutes after
initiating the mixing step, so have
everything ready mixing.
GENERAL PROPERTIES:
Appearance
Slight haze/ slight straw
Cure Type
Room temperature or Heat cure
Benefits
Resistant to many organic/inorganics
Strong bond strength
Great electrical insulator
Durable
Mix Ratio by weight
100:100 / Resin:Hardener
Substrates
metals, plastics, concrete, sheetrock, tile, marble, stone, rock, plaster,cement,glass fabrics, wood, leather and rigid plastics
Operating Temperature
-60 to 110 °C
Typical Application(s)
Anything requiring the unique properties this adhesive offers
UNCURED PROPERTIES:
Viscosity @ 25 °C, mPa∙s (cP)
Thixotropic
Solids Content
100%
Specific Gravity, mixed
1.2 g/cc
CURE SCHEDULE:
30 minutes
@ 65°C
2 hours
@ 25°C
MISC PROPERTIES:
Volume Resistivity
5.00e+11 ohm-cm
Dielectric Constant
4.8
Dielectric Strength
410kV/in
CTE, linear
33.3 μin/in-°F@ RT
Hardness, Shore D
70
GENERAL INFORMATION:
For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS)
.
HOW TO USE:
1)
Carefully clean and dry all surfaces to be bonded.
2)
Apply AA-BOND 201 completely mixed adhesive to the prepared surfaces, and gently press these surfaces together. Contact pressure
is adequate for strong, reliable bonds; however, maintain contact until adhesive is completely cured.
3)
Some separation of components is common during shipping and storage. For this reason, it is recommended that the contents of the
shipping container be thoroughly mixed prior to use.
4)
Some ingredients in this formulation provided may crystallize when subjected to low temperature storage. A gentle warming cycle of
52°C for 30 minutes prior to mixing components may be necessary. Crystallized epoxy components do not react as well as liquid
components
and should be re-dissolved prior to use for best results.
AVAILABILITY:
This epoxy can be supplied in various different packages.
Froo www.froo.com | Froo Cross Sell, Free Cross Sell, Cross promote, eBay Marketing, eBay listing Apps, eBay Apps, eBay Application