PC-7 EPOXY PASTE 1lb Cement Bonding Sealer Filler

Description

World Wide Shipping
Item Info:
Starting: $  -  Buy It Now: $  -  MAP: $  -  Shipping Weight: #Lbs
*Brand New Covered Under Manufacturer Warranty - See Return Policy Exception Below
- Item Info Here -
Usually Have More In Stock - If You Want More Then 1 Just Ask - Message or Call
Detailed Description & Features:
PC-7 EPOXY PASTE 1-Pound Cement, Bonding Sealer, Filler
Bonds most everything to anything
Heavy Duty Non-Drip Paste
As an Adhesive:
Wood, Metals, Glass, Brick, Block Rubber, Concrete, Stone, Slate, Hard Plastic, Fiber Glass, Tile in any and all combinations
As a Sealant:
Oil, Gas, and Water Tank Leaks, Cellar Cracks, Pressure Tanks, Plumbing Leaks
As a Filler:
Holes, Castings, Patterns, Molds, Voids, Welds, Steering Wheels and much more.
Saw-Drill-Tap-Mold-Sand-Paint-Machine
Description
PC-7 ® is a tough job Epoxy formulation developed for maximum bonding power. Components A (grey) and B (black), when mixed, react to form a bond of tremendous strength. PC-7 ® formulation provides extended working time, giving user ample time to complete larger jobs, reposition work or make changes. High wet grab or tack of PC-7 epoxy paste ® makes overhead and sidewall work easy without drip or sag. PC7 epoxy paste ® demonstrates excellent chemical resistance to mild acids, caustics, detergents, gasoline, fuel oil, salt, and fresh water. PC7 epoxy paste ® will not bond to wax paper, TEFLON ®, polyethylene, and some soft plastics. Test area when in doubt.
Mixing Tips
Approximately equal amounts of A and B by volume, variations of either compound as high as 20% will not affect bond strength. When desirable, one part of A to two parts of B may be used to increases elasticity (expansion joints,etc.). In cold or cool temperatures, place PC-7 epoxy paste containers near heat prior to using. PC-7 ® mixes and spreads easier at 80°F than at 40°F. Any smooth flat surface is an excellent surface for mixing and working. A small putty knife or flexible artist's spatula are excellent tools for both mixing and applying PC-7®.
Directions
Using separate knives (remove amount needed from cans), mix equal parts of A (lt. grey) and B (black) on flat surface until uniform in color. Surfaces to be bonded must be free of dirt, oil, rust, etc. Denatured alcohol or lacquer thinner are excellent for removing oil, fingerprints, etc. Rough up surfaces for best results. Normally, no vice or clamp needed, Prop or tape heavy objects to a wall or ceiling. At 70°F (21°C) PC-7 epoxy paste will remain workable in excess of one hour and cures for service overnight. Cure will be much faster at higher temperature than at low.
Application
Apply PC-7 ® in any thickness to both sides of surface and bring together firmly. Be careful to insure that ample PC-7 epoxy paste ® remains between the contact surfaces. To bridge or reinforce larger holes, screen wire or glass cloth is excellent. To smooth out work, dip tool in lacquer thinner or denatured alcohol. After cure, paint, drill, machine, sand, file, or saw PC-7 ®. ADVISE – Do not subject to sustained heat in excess of 200° (93°C). PC-7 ® has strength far exceeding most materials on which used. Speed cure with artificial heat.
Uses
AUTO-Seal : Gas tank, radiator and oil pan leaks. Bond: rear-view mirror brackets and mouldings. Fill: Holes, cracks and dents (metal or fiberglass). Rebuild: Steering wheels, etc.
CONTRACTOR-Bond: Re-bar, firring strips, anchors, brackets, plates, studs, thresholds to masonry. Patch holes and cracks. Repair cemetery headstones. Attach junction, switch, and fuse boxes and baseboard heating panels to wall.
HOME AND RANCH-Seal: Plumbing, fuel tanks, cellar cracks, and swimming pool leaks, etc. Repair: Equipment, machinery, furniture, and tools. Bond loose tile, ceramic fixtures, and flagstone.
RECREATION-Repair boats, R.V.'s, sporting goods and toys.
SHELF LIFE-Well in excess of two years.
Customer Comments
This stuff is magic. It will form a bond like nothing I've seen before. I've been using it for about 10 years and have never been unhappy with the results. I just used up my last batch filling in a 4x4 post that had a lot of deep dryrot (cleaned out the dry rot with a dremel)... some primer and paint and you cannot tell any work was done. It'll glue anything to anything....and is easy to work with.
I've even cast this into small emblems for my Triumph (made plaster casts, and then coated the inside with Vaseline as a release agent).
Note, you can smooth this once applied by using denatured alcohol....speed up curing by using a hair dryer on HOT.
*****
This is an amazing product. It never fails to succeed at the seemingly impossible jobs. Its unbelievable strength requries minimal surface area. The only downside is finding a way to hold your two pieces in place for the 24 hour curing time.
*****
Difficult to mix, very thick, almost like chewing gum, dries slowly, but amazingly strong, doesn't shrink, fills gaps, stays in place. Other adhesives are easier to use, but this stuff last forever and will work with almost anything
UPC # 00054983027776
Width: 0.20 IN
Multiplier: 1
Secondary UPC#: 00000000000000
Height: 0.15 IN
Future Promotional Numbers:
Master Pack: 48
Length: 0.33 IN
Basic/Expanded Item: Basic
If you can't see pictures, and/or hyperlinks are not working, try clicking the link below (if available)
-
Owner: Josh and Kate Vander Hyden
Ebay ID: frankforthardwareco
Skype: frankforthardware
Map
Item(s) may be available for pick up - pickup fee may apply
Sales Info:
We reserve the right to cancel an order in the event of a listing error.
(Errors such as: technical issues, pricing, availability, description, shipping regulations, miscalculations, etc...)
Any canceled orders will be promptly refunded.
All items are brand new unless otherwise specified. Brand new items are covered by manufacturer warranty.
(Will provide Manufacturer's phone numbers if needed.)
Shipping
:
Most payments take one full business day to process. Items will generally ship the day after payment is received.
We Will Ship Internationally
. International shipping may cost more.
Extra shipping costs & measures may need to be taken to ship your package.
Please be sensitive to this and willing to pay difference in cost if need be.
Some specials offered in the sale may not apply to internationally shipped items.
Returns:
If you want to return an item, please notify us within 14 days of receiving your purchase.
Please note, your refund will not include any of the shipping costs to or from you.
(only the auction end price will be refunded)
A 10% return fee may apply. If item is not returned exactly how it was sent your refund may be denied.
Return Policy Exception:
*"Covered Under Manufacturers Warranty" - when this is stated in the sale it is because it the item is brand new. If you experience any problems with your item you need to contact the manufacturer for parts, repair, replacement, etc...
We are simply a reseller, It is not our fault if it an brand new item "covered under manufacturers warranty" does not work properly or breaks. These types of problems need to be presented to the manufacturers /suppliers / distributors. Our profit margin is pennies on a dollar, don't be unfair and give negative or neutral feedback for something that is not in our control. This is the responsibility of the manufacturers /suppliers /distributors. So please point the finger in the correct direction, As the saying goes "don't shoot the messenger". We will provide you with company contact information if you need it, and if a company requests further information from you regarding the purchase you made from us we will be happy to communicate with them on your behalf to try and resolve any issues.
Payment Options:
Paypal, Credit Card, Credit Card by Phone, Etc...
If paying w/ credit or debit card you can pay normally through ebay or you can call and pay by phone. (231-352-9181, Frankfort Hardware) We will need to call the issuing bank of your credit card to verify your credit card is legitimate
and not stolen. We will only ship to the your credit card billing address (the address your credit card statment is mailed to)